Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Fence Installation: The West Palm Beach Owner’s Guide
Dvele fence installation in West Palm Beach typically runs $3,500 – $9,000 for a complete install, and we stock the brackets, posts, and panel hardware to get most Dvele homes squared away the same week we show up. Most owners call us after a storm blows a section loose, or they notice a gate dragging on its hinges and realize the post has shifted in our sandy soil. You should not have to chase down parts yourself or guess at compatibility. That’s our job.
We’re an independent service provider in West Palm Beach. Bradford Remodeling Co West Palm Beach has no corporate affiliation with Dvele, which means we tell you straight what a Dvele-spec part costs, what a quality equivalent saves you, and where it makes no sense to pay for the name.
Which Dvele Models This Applies To
Dvele builds each home around a set of exterior elevations rather than a menu of trim lines the way a production builder does, so we don’t chase model names. We match by measurement and material. Your fence section will be one of three things: horizontal channel siding with concealed fasteners, vertical tongue-and-groove, or a steel-framed privacy panel with a wood or composite skin. The post spacing matters more than the model plate.
Here’s the compatibility gotcha most people miss. Dvele fences use a non-standard post embedment depth for West Palm Beach. Most local fence crews set posts 24 inches deep and call it done. Dvele’s wind-load calcs assume 30 to 36 inches, because their spec was written for exposed coastal lots, not tucked-in suburban yards. A short-set post will fail in the first serious wind event we get here. That is the number one reason Dvele fence sections fail in Palm Beach County, and it’s the first thing we check when we walk the line.
For the finish surface, Dvele has used both real wood and a composite skin, and they do not mix. If your original install was composite, wood will read wrong at the seam. We verify material type during the estimate and match it. OEM panels run $180 – $260 per linear foot from Dvele’s parts channel when they’re available. A quality aftermarket match in the same profile usually lands between $95 and $150 per linear foot installed, and we’ll show you both numbers in writing before anything gets ordered.
Styles & brands we work with
Signs Your Dvele Fence Installation Is Failing
- Gate drags or won’t latch. In West Palm Beach, this is almost always a post that has settled back out of plumb in sandy soil. The hinge side sinks, the gate drops, the latch misses. Greasing the hinges buys you two weeks.
- Fence section leans 5 degrees or more. Wind load has started working the post loose below grade. Once the panel acts as a sail, every gust makes the hole bigger. Straightening without resetting the post is temporary.
- Concealed fasteners popping or panel edges lifting. This is moisture getting into the fastener line. West Palm Beach humidity and afternoon thunderstorms will find any gap in the seal line and work it open.
- Sections out of alignment at the seam. One panel should not sit proud of its neighbor. When you see a visible step between sections, either the post is twisting or the original install never hit true level across the run.
- Rust staining at post bases. On steel-framed Dvele panels, corrosion at grade level means the post’s protective coating has failed. South Florida salt air accelerates this. Left alone, it gets into the welded frame and the section is done.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Most Dvele fence jobs we do in West Palm Beach fall between $3,500 and $9,000. What drives the spread is linear footage, how many posts need to be reset at proper Dvele depth, and whether we’re pulling sections back into service or replacing them outright.
Here’s how the numbers typically break:
- Post reset (dig, prep, set at 30 – 36″, concrete): $85 – $140 per post
- Full post replacement with Dvele-spec steel post: $180 – $260 per post
- Fence panel replacement, aftermarket match: $95 – $150 per linear foot installed
- Gate rehang with new hinges and latch hardware: $250 – $450 per gate
- Full section demo and haul-off: $12 – $18 per linear foot
Everything on that list is a written line item before we start. You’ll see the parts cost and the labor cost separated. If the number changes for any reason once we’re in the ground, you get a call before we touch it. That’s Curtis Lane’s rule, and it’s been the rule on every Bradford job since 2004.
Every completed fence install carries our 365-Day Done Right Promise. If the work fails inside a year, we come back and correct it at no charge. The guarantee is in writing, signed, and in your hand before the crew packs up.
DIY or Call Us?
You can safely check two things. Walk the fence line and mark every post that’s more than a couple degrees out of plumb with a piece of tape. Then note which direction each panel leans. That’s useful information for whoever fixes it, and it takes ten minutes.
What you should not do is try to pull a leaning Dvele panel back straight with a come-along or a truck strap. The steel frames are under tension, and a panel that lets go will whip hard enough to break bone. We use proper bracing and lift points, and even then we treat a bound-up section like a loaded spring until it’s unbolted. Concrete work around a post base is also not a weekend job here. Get the hole the wrong depth and you’re right back to wind-load failure in a year, just $400 poorer.
If you want someone to walk the line and tell you exactly what’s sound and what isn’t, call (728) 203-9809. Estimates are free, and we won’t sell you a post you don’t need.
FAQs
A properly set Dvele fence in our climate should hold 12 to 15 years before panels need real attention, provided the posts went in at the correct 30 to 36 inch depth. West Palm Beach’s salt air and summer humidity will shorten that to 8 to 10 years if the coating or seal line was compromised at install. Call (728) 203-9809 if you want us to age your fence in person.
Most of the time, yes. If the posts are sound and the panels haven’t started corroding at the frame, we reset posts, re-align sections, and replace surface material where it’s failed. Replacement only becomes necessary when the steel frame itself is compromised or the panel has taken wind damage that can’t be pulled back true. We’ll show you the repair quote and the replacement quote side by side, and you decide with the numbers in front of you.
A typical repair with three to five posts needing re-set and one section replaced takes one day with our full crew. A full replacement of a 60-foot run usually runs two days. Concrete cure time is the only variable we can’t rush, and we won’t hang panels on posts that haven’t set.
We keep Dvele-compatible posts, fasteners, hinges, and latch hardware on the truck for the most common section profiles we see in the West Palm Beach area. If your home uses something we don’t stock, we order it during the estimate window so we’re not standing in your yard waiting on a parts delivery. We also work with KraftMaid, Cambria, and Silestone product lines, so if your Dvele home has other equipment that needs attention, we can handle that in the same visit.
Written by Curtis Lane, Owner, Bradford Remodeling Co – West Palm Beach at Bradford Remodeling Co West Palm Beach, serving West Palm Beach and nearby areas.
