Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Therma-Tru Fence Installation: The West Palm Beach Owner’s Guide
Therma-Tru fence installation in West Palm Beach typically runs $3,500 – $9,000 installed, including materials, hardware, concrete footings, and labor. Most projects we handle are finished in two to four days, weather permitting. Homeowners usually find us after a storm has pushed a section out of plumb, a post has rotted at the base, or a gate has started dragging against the latch plate.
Bradford Remodeling Co West Palm Beach is an independent service provider. We are not affiliated with Therma-Tru, but we install and service Therma-Tru fence systems alongside their door product lines. Therma-Tru is known for doors, but their composite and vinyl fence components show up across Palm Beach County, and they fail in predictable ways here: salt air, sandy soil, and summer downpours all take a toll.
Which Therma-Tru Models This Applies To
Therma-Tru fence systems break into two main lines: their composite privacy panels and their vinyl post-and-rail systems. The composite panels use a tongue-and-groove profile that locks into aluminum or composite rails. The vinyl line uses hollow posts with routed channels. Both are common in West Palm Beach HOAs and gated communities from El Cid to Ibis Golf and Country Club.
Identifying your part is straightforward. Look for a small raised logo on the inside face of the panel or on the top rail. If the logo is worn off, measure the panel width: Therma-Tru composite panels are typically 6 feet or 8 feet wide, with a 6-inch tongue overlap. The rail channels accept a nominal 3/4-inch panel profile. Aftermarket panels often run a true 3/4-inch thickness, while OEM Therma-Tru composite sits at 11/16-inch. That 1/16-inch difference is enough to cause a panel to sit loose and rattle in the wind. We match OEM specifications rather than forcing a generic part into a sloppy fit.
We stock common Therma-Tru-compatible rail, post, and gate hardware on the truck. For full panel replacements, we order OEM or spec-matched aftermarket panels through our supplier network and have them in hand within three to five business days.
Styles & brands we work with
Signs Your Therma-Tru Fence Installation Is Failing
- Leaning posts at the gate. The gate post carries more load than any other post. In West Palm Beach’s sandy soil, a 24- to 30-inch footing is the minimum for a gate post. If the original installer stopped at 18 inches, the post starts to lean within two years. The fix is resetting the post with a deeper, properly tamped concrete footing.
- Panels blown out of the top rail. High wind gusts during summer storms can lift a loose panel straight out of its channel. We see this most often on west-facing fence lines in areas like Bear Lakes and Andros Isle. The cause is usually a rail channel that was notched too wide at the factory or a panel that was cut short.
- Faded or chalky composite surface. Therma-Tru composite panels hold color well, but after five to seven years in direct Florida sun, the surface starts to oxidize. You will see a white chalk film wipe off onto your hand. This is cosmetic, not structural, but it is a sign the panel has absorbed enough UV to begin weakening.
- Gate dragging or failing to latch. The gate settles as the hinge post shifts or the hinge screws work loose in the composite. Rather than resetting hinges repeatedly, the correct repair is to re-align the gate and replace the hinge hardware with stainless steel brackets rated for exterior coastal use.
- Puddling water around post bases. If water pools at the base of a post after rain, the concrete footing may have been poured below grade. That trapped moisture rots the post base or corrodes the post anchor over time. The repair is lifting the post, re-pouring the footing proud of grade, and re-securing the bracket.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Therma-Tru fence installation in West Palm Beach, a full replacement of a typical 50- to 80-linear-foot run runs $3,500 – $9,000. A single gate post reset is at the low end of that range. A full perimeter replacement with two gates, new rails, and all new composite panels is at the high end. Here is the line-item breakdown:
- Post removal and reset with new concrete footings: $75 – $150 per post
- Rail replacement (composite or aluminum, per 8-foot section): $40 – $85 per rail
- Composite panel replacement (per 6-foot panel): $90 – $180 per panel
- Gate re-hang with new stainless hardware: $250 – $600 per gate
- Full fence removal and disposal: $500 – $1,200
Every line item is in writing before work starts. That is the Bradford way: a written price, no numbers moving at the door. The labor and parts carry the 365-Day Done Right Promise. If the repair fails inside a year, we come back and fix it at no charge.
DIY or Call Us?
You can safely replace a single vinyl panel if the old one is cracked and the rails are still solid. Measure the panel width, order the matching profile, and slide it into the channel from the top. Most homeowners can handle that in an afternoon.
What you should not do is reset a gate post or rebuild a section after a storm. Digging a proper footing in West Palm Beach means going deep enough to get past the sand and into stable earth, and it means accounting for the water table when we have had a wet season like this one. If the footing is wrong, the post leans again within a season, and you are paying twice. We are happy to look at the site and tell you honestly whether it is a homeowner job or a crew job. Call (728) 203-9809 for a straight opinion, no pressure either way.
FAQs
A properly installed Therma-Tru composite fence lasts 15 to 20 years in South Florida’s climate. Vinyl post-and-rail systems run 10 to 15 years before the posts begin to show UV brittleness. The posts fail before the panels in nearly every case we see, which is why we pour deeper footings than the bare minimum.
Yes, if the post itself is not cracked or rotted, we can often straighten and re-set it in a new concrete footing. If the post is composite and the base has softened from water exposure, replacement is the better option. Call (728) 203-9809 and we will tell you which path makes sense before quoting anything.
A single gate re-hang or post reset takes half a day on site. A full fence section replacement with new rails and panels runs two to four days depending on the linear footage and how many gates are involved. We schedule a concrete cure time of at least 24 hours before rehanging a gate on a new footing.
We stock common rail channel, stainless gate hardware, and post brackets in our West Palm Beach trucks. Full composite panels and custom rail lengths are ordered to spec and arrive within three to five business days. We will tell you at the estimate what is in stock and what needs to be ordered.
Ready to get your Therma-Tru fence squared away? Curtis Lane and the Bradford Remodeling Co West Palm Beach crew will give you a written price before any work starts. Call (728) 203-9809 to schedule your free estimate.
Written by Curtis Lane, Owner, Bradford Remodeling Co – West Palm Beach at Bradford Remodeling Co West Palm Beach, serving West Palm Beach and nearby areas.
